è¿ä¸ªæ¯æè£åå¦éé¢çä¸ä¸ªå®å½ä»¤ï¼åç¬æ
åµä¸ä½¿ç¨æ¯æ²¡æçï¼è¦æä¸å®çå
¶ä»å½ä»¤é
åï¼ææä¹å°±ä¸å°½ç¸åï¼å¤çæ¹æ³ä¹å°±ä¸ä¸æ ·äºï¼æ以è¿ä¸ªå½ä»¤ç使ç¨å»ºè®®æ¥¼ä¸»åèæè£åå¦çåæç¥è¯;
è±æ说ææ¯è¾æ¸
æ¥ç¹ï¼
Structural Guide |
Chapter 12. Fracture Mechanics
è¿ä¸ªå½ä»¤ç使ç¨å ä¹éè¦å
¨é¨çæè£åå¦çç¥è¯ï¼
CTMOPT,Option,Val1,Val2
Sets crack tip meshing options for fracture mechanics.
Valid Option values are:
DEFAULT
Resets all options to default values.
STATUS
Lists the current status of all options.
CONFIG
Specifies the crack type and the symmetry condition.
Valid Val1 values:
THROUGH -- Through crack (default)
SURFACE -- Surface crack
Valid Val2 values:
FULL -- Full crack (default)
HALF -- Half crack
QUARTER -- Quarter crack
VOLUME
Val1 -- An existing volume number. A value is required for this option.
LENGTH
Val1 -- Crack length. A value is required for this option.
DEPTH
Val1 -- Crack depth. Valid only for surface (SURFACE) cracks. The default value is half of the crack length (LENGTH / 2).
CNAME
Val1 -- Crack node component. Specify this value in uppercase characters only, enclosed in single quotation marks. Example: 'NODECOMP1'
BLNG
Val1 -- Length of blocks on either side of a through crack (THROUGH). Use this value to sector the length along the sides of the crack into a precise number of elements, or to sector elements of a precise size. The default value is the crack length (LENGTH), where the entire length is devoted to one block.
BWID
Val1 -- Width of blocks on either side of a through crack (THROUGH). The default value is the crack length (LENGTH).
CEXT
Val1 -- Greater-than distance from the working plane to the back of the through crack (THROUGH) crack initial volume. The default value is five times the crack length (5 * LENGTH)
NETH
Val1 -- Number of elements around the crack tip in the THETA direction. The default value derives from the PREP7 command KSCON.
ESCZ
Val1 -- Element size radially outward from crack. The default value is one-tenth of the block width (BWID / 10) for a through crack (THROUGH), or one-tenth of the crack zone radius (radius / 10) for a surface crack (SURFACE).
NROW
Val1 -- Number of rows of elements around the crack tip in a radial direction. The default value is 3.
ETHK
Val1 -- Number of elements through the thickness of a through crack (THROUGH). The default value is 3.
ESZB
Val1 -- Element size along surface crack (SURFACE) zone boundaries. The default value is one-fourth of the crack (LENGTH / 4).
QUAD
Val1 -- Set this value to 1 to generate quad element faces on surface crack (SURFACE) zone boundaries. The default is triangles.
HELP
Lists this helps information.
ä¸é¢æ¯ä¸äºè¯´æï¼ä½æ¯æä¸é¢çè¿ä¸ªï¼è¯å®ä¸å¤ç解è¿ä¸ªå½ä»¤ï¼
温馨提示:答案为网友推荐,仅供参考